Development of Fly Ash-Based Geopolymer Lightweight Aggregates
DOI:
https://doi.org/10.31272/jeasd.28.5.7Keywords:
Alkali-activated fly ash, Fly ash-based geopolymer, Geopolymer aggregates, Lightweight aggregates, Microwave hybrid heating, Sintered fly ash aggregatesAbstract
This research delves into the utilization of microwave hybrid heating as a curing technique for producing fine aggregates from fly ash. Various concentrations of alkali activator solutions were employed as binders to pelletize the fly ash (ranging from 0% to 10%). The resultant green fly ash-based geopolymer (FAG) aggregates were subjected to a 15-minute microwave kiln treatment. The microwave-sintered FAG fine aggregates, varying in sizes from 0.60 to 2.36 mm, were then utilized to fabricate 50 mm cubic cement mortar samples. Findings indicated that the density of FAG aggregates was approximately 36% lower than that of natural sand, while the water absorption capacity of FAG aggregates exhibited a fivefold increase compared to natural sand. Notably, cement mortar samples made with FAG aggregate of 4% alkali activator exhibited maximum compressive strengths of 31, 37, and 42 MPa at 7, 14, and 28 days of curing, respectively. These compressive strengths were only 12% lower than those of cement mortars made with natural sand across all curing periods. The use of microwave hybrid heating to transform fly ash into aggregates with sufficient strength appears viable, suggesting that these manufactured FAG aggregates could serve as substitutes for natural aggregates in concrete production
References
M. Mathapati, K. Amate, C. D. Prasad, M.L. Jayavardhana, and T. H. Raju, “A review on fly ash utilization,” Materials Today: Proceedings, vol. 50, part 5, pp. 1535-1540, Feb 2022, https://doi.org/10.1016/j.matpr.2021.09.106
A. Graytee, J. G. Sanjayan, and A. Nazari, “Development of a High Strength Fly ash-based Geopolymer in Short Time by Using Microwave Curing,” Ceramics International, vol. 44, no. 7, pp. 8216–8222, May 2018, doi: https://doi.org/10.1016/j.ceramint.2018.02.001.
Z. A. Mohammed, L. A. Al-Jaberi, A. N. Shubber “Effect of Polypropylene Fiber on Properties of Geopolymer Concrete Based Metakolin”, Journal of Engineering and Sustainable Development, vol. 25, no. 2, pp. 58–67, Mar. 2021, doi: https://doi.org/10.31272/jeasd.25.2.7.
A. Sarabèr, R. Overhof, T. Green, and J. Pels, “Artificial lightweight aggregates as utilization for future ashes – A case study,” Waste Management, vol. 32, no. 1, pp. 144-152. Jan 2012, https://doi.org/10.1016/j.wasman.2011.08.017.
G. F. Kheder, “Variation in Mechanical Properties of Natural and Recycled Aggregate Concrete as Related to the Strength of Their Binding Mortar,” Materials and Structures, vol. 38, no. 281, pp. 701–709, Jan. 2005, doi: https://doi.org/10.1617/14216
Bijen, J.M.J.M., “Manufacturing processes of artificial lightweight aggregates from fly ash,” International Journal of Cement Composites and Lightweight Concrete, vol. 8, no. 3, pp. 191-199, Aug 1986, https://doi.org/10.1016/0262-5075(86)90040-0
W. Pietsch, Agglomeration in Industry, 1st ed., Weinheim, Germany, Wiley-VCH Verlag GmbH & Co. KGaA, 2005.
Aggregate Industries Introduction to Lytag lightweight aggregate, Technical Manual - Section 1, Laytag Ltd., London, UK, 2017. https://www.aggregate.com/
F. Tajra, M. A. Elrahman, and D. Stephan, “The production and properties of cold-bonded aggregate and its applications in concrete: A review,” Construction and Building Materials, vol. 225, pp. 29-43, Nov 2019, https://doi.org/10.1016/j.conbuildmat.2019.07.219
J. Lin, K. H. Mo, Y. Goh, and C. C. Onn, “Potential of municipal woody biomass waste ash in the production of cold-bonded lightweight aggregates,” Journal of Building Engineering, vol. 63, part A, Jan 2023, https://doi.org/10.1016/j.jobe.2022.105392
A. Ferraro, V. Ducman, F. Colangelo, L. Korat, D. Spasiano, et al., “Production and characterization of lightweight aggregates from municipal solid waste incineration fly-ash through single- and double-step pelletization process,” Journal of Cleaner Production, vol. 383, Jan 2023, https://doi.org/10.1016/j.jclepro.2022.135275
T. Bakharev, “Geopolymeric materials prepared using Class F fly ash and elevated temperature curing,” Cement and Concrete Research, vol. 35, no. 6, p. 1224-1232, Jun 2005, https://doi.org/10.1016/j.cemconres.2004.06.031
H. Fansuri, D. Prasetyoko, Z. Zhang, and D. Zhang, “The effect of sodium silicate and sodium hydroxide on the strength of aggregates made from coal fly ash using the geopolymerisation method,” Asia-Pacific Journal of Chemical Engineering, vol. 7, no. 1, pp. 73-79, Aug 2012, https://doi.org/10.1002/apj.493
T. Garnault, D. Bouvard, J. Chaix, S. Marinel, and C. Harnois, “Is direct microwave heating well suited for sintering ceramics?,” Ceramics International, vol. 47, no. 12, pp. 16716-16729, Jun 2021, https://doi.org/10.1016/j.ceramint.2021.02.242
H. Curto, A. Thuault, F. Jean, M. Violier, V. Dupont, et al., “Coupling additive manufacturing and microwave sintering: A fast processing route of alumina ceramics,” Journal of the European Ceramic Society, vol. 40, no. 7, pp.2548-2554, Jul 2020, https://doi.org/10.1016/j.jeurceramsoc.2019.11.009
T. Amiri, T.H. Etsell, and P. Sarkar, “Direct Microwave Sintering of Poorly Coupled Ceramics in Electrochemical Devices,” Journal of Electrochemical Science and Technology, vol. 13, no. 3, pp. 390-397, Jul 2022, https://doi.org/10.33961/jecst.2022.00290
A. Goulas, T. Whittaker, G. Chi-Tangyie, I. M. Reaney, D. Engstrøm, et al., “Multi-material additive manufacture and microwave-assisted sintering of a metal/ceramic metamaterial antenna structure,” Applied Materials Today, vol. 33, Aug 2023, https://doi.org/10.1016/j.apmt.2023.101878
T. P. Naik, I. Singh, and A. K. Sharma, “Processing of polymer matrix composites using microwave energy: A review,” Composites Part A: Applied Science and Manufacturing, vol. 156, May 2022, https://doi.org/10.1016/j.compositesa.2022.106870
M. Dua, Q. Zhang, and P. Mertiny, “Microwave heating of graphene nanoplatelet polymer composites: Experimental and finite element study,” Polymer Composites, vol. 44, no. 8, pp. 4924-4936, May 2023, https://doi.org/10.1002/pc.27460
M. Maqbool, M. Asif, M. Yousaf, Y. Zhang, W. Aftab, et al., “Microwaves heating strategy to synthesize few layer graphene for polymer composites towards thermal and electrical applications,” Composites Science and Technology, vol. 200, Nov 2020, https://doi.org/10.1016/j.compscitech.2020.108402
M. Thirunavukkarasu, J. Venkatesh, N. M. Jasmin, A. Nikhil, K.K. Arun, et al., “Optimal parameters of microwave sintering process on nickel based composite,” Materials Today: Proceedings, vol. 66, part 3, pp. 653-657, Apr 2022, https://doi.org/10.1016/j.matpr.2022.03.518
S. Moratal, E. Rosado, R. Benavente, M. D. Salvador, F. L. Peñaranda-Foix, et al., “Fast-low temperature microwave sintering of ZrSiO4–ZrO2 composites,” Ceramics International, vol. 49, no. 13, pp. 21652-21657, Jul 2023, https://doi.org/10.1016/j.ceramint.2023.03.301
P. Kumar, R.C. Singh, and R. Lal, “Fabrication of bio metallic titanium and titanium alloys by microwave energy–A review,” Results in Surfaces and Interfaces, vol. 14, Feb 2024, https://doi.org/10.1016/j.rsurfi.2024.100199
A. Buasri, W. Keereekongsakol, U. Phuttharaksa, and V. Loryuenyong, “Microwave heating for the production of red-emitting sintered waste glass containing rare-earth ions,” Results in Optics, vol. 15, May 2024, https://doi.org/10.1016/j.rio.2024.100633
K. Kashimura, T. Miyata, A. Oshita, N. Omoto, T. Fujii, et al., “Microwave sintering of carbon fly ash containing garnet and sodium chloride,” Fuel, vol. 316, May 2022, https://doi.org/10.1016/j.fuel.2022.123217
K. Yeung, C. Tang, R. Hu, C. Lam, W. Law, et al., “Fabrication of ceramic bioscaffolds from fly ash cenosphere by susceptor-assisted microwave sintering,” Journal of the European Ceramic Society, vol. 42, no. 10, pp. 4410-4419, Aug 2022, https://doi.org/10.1016/j.jeurceramsoc.2022.03.046
T. Fujii, K. Kashimura, and H. Tanaka, “Microwave sintering of fly ash containing unburnt carbon and sodium chloride,” Journal of Hazardous Materials, vol. 369, pp. 318-323, May 2019, https://doi.org/10.1016/j.jhazmat.2018.12.114
G. Baykal, and A.G. Döven, “Utilization of fly ash by pelletization process; theory, application areas and research results,” Resources, Conservation and Recycling, vol. 30, no. 1, pp. 59-77, Jul 2000, https://doi.org/10.1016/S0921-3449(00)00042-2
H. Arslan, and G. Baykal, “Utilization of fly ash as engineering pellet aggregates,” Environmental Geology, vol. 50, pp. 761-770, Mar 2006, https://doi.org/10.1007/s00254-006-0248-7
J.P. Ollivier, J.C. Maso, and B. Bourdette, “Interfacial transition zone in concrete,” Advanced Cement Based Materials, vol. 2, no. 1, pp. 30-38, Jan 1995, https://doi.org/10.1016/1065-7355(95)90037-3
S. Mindess, and S. Diamond, “A preliminary SEM study of crack propagation in mortar,” Cement and Concrete Research, vol. 10, no. 4, pp. 509-519, Jul 1980, https://doi.org/10.1016/0008-8846(80)90095-2
M.-H Zhang, and O.E. Gjørv, “Microstructure of the interfacial zone between lightweight aggregate and cement paste,” Cement and Concrete Research, vol. 20, no. 4, pp. 610-618, Jul 1990, https://doi.org/10.1016/0008-8846(90)90103-5
Y.B. Zaitsev, and F.H. Wittmann, “Simulation of crack propagation and failure of concrete,” Matériaux et Construction, vol. 14, no. 5, pp. 357-365, Sep 1981, https://doi.org/10.1007/BF02478729
F.H. Wittmann, “Crack formation and fracture energy of normal and high strength concrete,” Sadhana, vol. 27, pp. 413-423, Aug 2002, https://doi.org/10.1007/BF02706991
B. Hillemeier, and H.K. Hilsdorf, “Fracture mechanics studies on concrete compounds,” Cement and Concrete Research, vol. 7, no. 5, pp. 523-535, Sep 1977, https://doi.org/10.1016/0008-8846(77)90114-4
A. Elsharief, M.D. Cohen, and J. Olek, “Influence of aggregate size, water cement ratio and age on the microstructure of the interfacial transition zone,” Cement and Concrete Research, vol. 33, no. 11, pp. 1837-1849, Nov 2003, https://doi.org/10.1016/S0008-8846(03)00205-9
P.J.M. Monteiro, J.C. Maso, and J.P. Ollivier, “The aggregate-mortar interface,” Cement and Concrete Research, vol. 15, no. 6, pp. 953-958, Nov 1985, https://doi.org/10.1016/0008-8846(85)90084-5
W.A. Tasong, C.J. Lynsdale, and J.C. Cripps, “Aggregate-cement paste interface. ii: influence of aggregate physical properties,” Cement and Concrete Research, vol. 28, no. 10, pp. 1453-1465, Oct 1998, https://doi.org/10.1016/S0008-8846(98)00126-4
D. Breton, A. Carles-Gibergues, G. Ballivy, and J. Grandet, “Contribution to the formation mechanism of the transition zone between rock-cement paste,” Cement and Concrete Research, vol. 23, no. 2, pp. 335-346, Mar 1993, https://doi.org/10.1016/0008-8846(93)90099-U
A. A., Kadhim, et al. "Improvement fatigue life and strength of isotropic hyper composite materials by reinforcement with different powder materials." International Journal of Mechanical & Mechatronics Engineering. vol 18, no. 2, pp. 77-86, 2018. https://www.academia.edu/download/95217887/181302-9494-IJMME-IJENS.pdf
Downloads
Key Dates
Received
Revised
Accepted
Published Online First
Published
Issue
Section
License
Copyright (c) 2024 Ahmed Graytee, Hayder A. Mehdi (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
