Plasma-Induced Surface Functionalization of Polymer Powders for Integration into UV-Resistant Functional Composites
DOI:
https://doi.org/10.31272/jeasd.3614Keywords:
Crystallization, Differential Scanning Calorimetry (DSC), Morphology, Plasma treatment, Polyamide 12, Thermal stability, Thermogravimetric Analysis (TGA), WettabilityAbstract
This study investigates the effects of plasma surface treatment on the thermal and morphological properties of polyamide 12 (PA12) powder. The powders were treated for 1 h and 2 h under full power in an air environment. Thermogravimetric analysis (TGA) results demonstrated that the plasma action improved the maximum decomposition temperature from 449.3 °C for the untreated polyamide 12 to 461.7 °C for the 2-h-treated sample, indicating improved thermal stability. The analysis of differential scanning calorimetry (DSC) revealed a marked increase in the temperature of crystallization (Tc) from 133.31 °C for the untreated PA12 sample to 141.7 °C for the 2-h sample, while the melting temperature is approximately constant at 185 °C. The SEM images demonstrated that plasma treatment resulted in a roughened, more homogeneous surface morphology with significantly fewer surface defects and irregularities. Plasma treatment enhanced the wettability and water dispersion of PA12, as plasma-treated powders showed fast spreading and stable suspension in water due to the introduction of polar groups and increased surface pores. The change from a water-hating grouping to a water-loving scattering provides a strong basis for water-based processing and future composite design that will need strong interfacial interactions. Thus, these results confirmed the importance of plasma treatment as an environmentally friendly method in tailoring the properties of PA12 for UV-resistant applications.
References
A. Touris, A. Turcios, E. Mintz, S. R. Pulugurtha, P. Thor, M. Jolly, and U. Jalgaonkar, “Effect of molecular weight and hydration on the tensile properties of polyamide 12,” Results in Materials, vol. 8, Art. no. 100149, 2020. doi: https://doi.org/10.1016/j.rinma.2020.100149.
N. Ma, W. Liu, L. Ma, S. He, H. Liu, Z. Zhang, A. Sun, M. Huang, and C. Zhu, “Crystal transition and thermal behavior of Nylon 12,” e-Polymers, vol. 20, no. 1, pp. 346–352, 2020. doi: https://doi.org/10.1515/epoly-2020-0039.
C. Cai, W. S. Tey, J. Chen, W. Zhu, X. Liu, T. Liu, L. Zhao, and K. Zhou, “Comparative study on 3D printing of polyamide 12 by selective laser sintering and multi jet fusion,” Journal of Materials Processing Technology, vol. 288, Art. no. 116882, 2021. doi: https://doi.org/10.1016/j.jmatprotec.2020.116882.
S. Rosso, R. Meneghello, L. Biasetto, L. Grigolato, G. Concheri, and G. Savio, “In-depth comparison of polyamide 12 parts manufactured by Multi Jet Fusion and Selective Laser Sintering,” Additive Manufacturing, vol. 36, Art. no. 101713, 2020.doi: https://doi.org/10.1016/j.addma.2020.101713.
A. J. Cano, A. Salazar, and J. Rodríguez, “Effect of temperature on the fracture behavior of polyamide 12 and glass-filled polyamide 12 processed by selective laser sintering,” Engineering Fracture Mechanics, vol. 203, pp. 66–80, 2018. doi: https://doi.org/10.1016/j.engfracmech.2018.07.035.
Y. C. Ching, T. U. Gunathilake, K. Y. Ching, C. H. Chuah, V. Sandu, R. Singh, and N. S. Liou, “Effects of high temperature and ultraviolet radiation on polymer composites,” in Durability and Life Prediction in Biocomposites, Fibre-Reinforced Composites and Hybrid Composites, Duxford, U.K.: Woodhead Publishing, 2019, pp. 407–426. doi: https://doi.org/10.1016/B978-0-08-102290-0.00018-0.
T. Puttonen, M. Salmi, and J. Partanen, “Mechanical properties and fracture characterization of additive manufacturing polyamide 12 after accelerated weathering,” Polymer Testing, vol. 104, Art. no. 107376, 2021. doi: https://doi.org/10.1016/j.polymertesting.2021.107376.
N. D. Wanasekara, V. Chalivendra, and P. Calvert, “Effect of accelerated ultraviolet and thermal exposure on nanoscale mechanical properties of nylon fibers,” Polymer Engineering & Science, vol. 52, no. 11, pp. 2482–2488, 2012. doi: https://doi.org/10.1002/pen.23204.
T. Stiller, E. Truszkiewicz, T. Schrank, B. Haar, G. Meier, W. Kraschitzer, G. Pinter, J. Lackner, and M. Berer, “Polyamide 12 powder ageing in laser beam-based powder bed fusion and its combined effects on powder and component characteristics,” Rapid Prototyping Journal, vol. 31, no. 11, pp. 82–96, 2025. https://doi.org/10.1108/RPJ-08-2024-0351.
L. Lanzl, K. Wudy, and D. Drummer, “The effect of short glass fibers on the process behavior of polyamide 12 during selective laser beam melting,” Polymer Testing, vol. 83, Art. no. 106313, 2020. doi: https://doi.org/10.1016/j.polymertesting.2019.106313.
S. Roy, T. Das, L. Zhang, Y. Li, Y. Ming, S. Ting, and C. Y. Yue, “Triggering compatibility and dispersion by selective plasma-functionalized carbon nanotubes to fabricate tough and enhanced Nylon 12 composites,” Polymer, vol. 58, pp. 153–161, 2015. doi: https://doi.org/10.1016/j.polymer.2014.12.032.
P. Latko-Durałek, J. Rzempołuch, M. Staniszewska, K. Rosłoniec, M. Bil, R. Kozera, and A. Boczkowska, “The antifungal fibers of polyamide 12 containing silver and metal oxides,” Materials, vol. 16, no. 17, Art. no. 5837, 2023.doi: https://doi.org/10.3390/ma16175837.
X. Liu, W. S. Tey, J. Y. C. Choo, J. Chen, P. Tan, C. Cai, and K. Zhou, “Enhancing the mechanical strength of Multi Jet Fusion–printed polyamide 12 and its glass fiber-reinforced composite via high-temperature annealing,” Additive Manufacturing, vol. 46, Art. no. 102205, 2021. doi: https://doi.org/10.1016/j.addma.2021.102205.
M. Pavan, M. Faes, D. Strobbe, B. Van Hooreweder, T. Craeghs, D. Moens, and W. Dewulf, “On the influence of inter-layer time and energy density on selected critical-to-quality properties of PA12 parts produced via laser sintering,” Polymer Testing, vol. 61, pp. 386–395, 2017. doi: https://doi.org/10.1016/j.polymertesting.2017.05.027.
G. Wang, P. Wang, Z. Zhen, W. Zhang, and J. Ji, “Preparation of PA12 microspheres with tunable morphology and size for use in SLS processing,” Materials & Design, vol. 87, pp. 656–662, Dec. 2015. doi: https://doi.org/10.1016/j.matdes.2015.08.083.
S. Josupeit, L. Ordia, and H.-J. Schmid, “Modelling of temperatures and heat flow within laser sintered part cakes,” Additive Manufacturing, vol. 12, pp. 189–196, 2016. doi: https://doi.org/10.1016/j.addma.2016.06.002.
P. Chen, M. Tang, W. Zhu, L. Yang, S. Wen, C. Yan, H. Nan, and Y. Shi, “Systematical mechanism of polyamide-12 aging and its micro-structural evolution during laser sintering,” Polymer Testing, vol. 67, pp. 370–379, 2018. doi: https://doi.org/10.1016/j.polymertesting.2018.03.035.
H. J. O’Connor and D. P. Dowling, “Comparison between the properties of polyamide 12 and glass-bead filled polyamide 12 using the Multi Jet Fusion printing process,” Additive Manufacturing, vol. 31, Art. no. 100961, Jan. 2020. doi: https://doi.org/10.1016/j.addma.2019.100961.
L. Lanzl, K. Wudy, S. Greiner, and D. Drummer, “Selective laser sintering of copper-filled polyamide 12: Characterization of powder properties and process behavior,” Polymer Composites, vol. 40, no. 5, pp. 1801–1809, 2019. doi: https://doi.org/10.1002/pc.24940.
G. Primc, “Surface modification of polyamides by gaseous plasma—Review and scientific challenges,” Polymers, vol. 12, no. 12, Art. no. 3020, 2020. doi: https://doi.org/10.3390/polym12123020.
M. Bahrami, D. Lavayen-Farfan, M. A. Martínez, and J. Abenojar, “Experimental and numerical studies of polyamide 11 and 12 surfaces modified by atmospheric pressure plasma treatment,” Surfaces and Interfaces, vol. 32, Art. no.102154, 2022. doi: https://doi.org/10.1016/j.surfin.2022.102154.
J. Hnilica, L. Potočňáková, M. Stupavská, and V. Kudrle, “Rapid surface treatment of polyamide 12 by microwave plasma jet,” Applied Surface Science, vol. 288, pp. 251–257, 2014. doi: https://doi.org/10.1016/j.apsusc.2013.10.016.
D. Pappas, A. Bujanda, J. D. Demaree, J. K. Hirvonen, W. Kosik, R. Jensen, and S. McKnight, “Surface modification of polyamide fibers and films using atmospheric plasmas,” Surface and Coatings Technology, vol. 201, no. 7, pp. 4384–4388, 2006. doi: https://doi.org/10.1016/j.surfcoat.2006.08.068.
S. Petzold, J. Klett, A. Schauer, and T. A. Osswald, “Surface roughness of polyamide 12 parts manufactured using selective laser sintering,” Polymer Testing, vol. 80, Art. no. 106094, 2019. doi: https://doi.org/10.1016/j.polymertesting.2019.106094.
D. Verdi, D. Merino-Millán, and A. Salazar, “Metallisation of additive manufactured polyamide 12 by low pressure cold spray,” Surface and Coatings Technology, vol. 479, Art. no.130484, 2024. doi: https://doi.org/10.1016/j.surfcoat.2024.130484.
J. Yip, K. Chan, K. M. Sin, and K. S. Lau, “Low temperature plasma-treated nylon fabrics,” Journal of Materials Processing Technology, vol. 123, no. 1, pp. 5–12, 2002. doi: https://doi.org/10.1016/S0924-0136(02)00024-9.
R. A. Jelil, “A review of low-temperature plasma treatment of textile materials,” Journal of Materials Science, vol. 50, no. 18, pp. 5913–5943, 2015. https://doi.org/10.1007/s10853-015-9152-4.
A. A. Tyuftin and J. P. Kerry, “Review of surface treatment methods for polyamide films for potential application as smart packaging materials: Surface structure, antimicrobial and spectral properties,” Food Packaging and Shelf Life, vol. 24, Art. no. 100475, 2020. doi: https://doi.org/10.1016/j.fpsl.2020.100475.
C. Che, B. Dashtbozorg, S. Qi, M. J. North, X. Li, H. Dong, and M. J. Jenkins, “The ageing of μPlasma-modified polymers: The role of hydrophilicity,” Materials, vol. 17, no. 6, Art. no.1402, 2024. doi: https://doi.org/10.3390/ma17061402
A. Almansoori, R. Seabright, C. Majewski, and C. Rodenburg, “Feasibility of plasma treated clay in clay/polymer nanocomposites powders for use Laser Sintering (LS),” IOP Conference Series: Materials Science and Engineering, vol. 195, no. 1,012003, 2017.doi: https://doi.org/10.1088/1757-899X/195/1/012003.
A. Almansoori and W. Alkaron, “Effect of low-pressure plasma treatment on the thermal behaviour of organo-modified montmorillonite nanoclay,” Archives of Materials Science and Engineering, vol. 125, no. 1, pp. 5–14, 2024. doi: https://doi.org/10.5604/01.3001.0054.4729.
T. Stichel, T. Frick, T. Laumer, F. Tenner, T. Hausotte, M. Merklein, and M. Schmidt, “A round robin study for selective laser sintering of polyamide 12: Microstructural origin of the mechanical properties,” Optics & Laser Technology, vol. 89, pp. 31–40, 2017. doi: https://doi.org/10.1016/j.optlastec.2016.09.042.
W. Zhang, L. Johnson, S. R. P. Silva, and M. K. Lei, “The effect of plasma modification on the sheet resistance of nylon fabrics coated with carbon nanotubes,” Applied Surface Science, vol. 258, no. 20, pp. 8209–8213, 2012. doi: https://doi.org/10.1016/j.apsusc.2012.05.023.
H. W. B. Teo, T. Van Thai, C. Tang, K. Chen, J. Zeng, and H. Du, “Effects of additives and pre-heating temperature on interlayer shrinkage of polyamide-12 parts in Additive Manufacturing,” Polymer, vol. 327, Art. no. 128409, 2025. doi: https://doi.org/10.1016/j.polymer.2025.128409
D. W. van Krevelen and K. te Nijenhuis, Properties of Polymers: Their Correlation with Chemical Structure; Their Numerical Estimation and Prediction from Additive Group Contributions, 4th ed. Amsterdam, The Netherlands: Elsevier, 2009. doi: https://doi.org/10.1016/C2009-0-05459-2.
M. Arioli, L. Franco, and J. Puiggalí, “Non-isothermal crystallization and thermal degradation studies on nylons 7,10 and 10,7 as isomeric odd-even and even-odd polyamides,” Thermochimica Acta, vol. 735, Art. no. 179721, 2024. doi: https://doi.org/10.1016/j.tca.2024.179721.
M. Kohutiar, L. Kakošová, M. Krbata, R. Janík, J. J. Fekiač, A. Brezničká, M. Eckert, P. Mikuš, and Ľ. Timárová, “Comprehensive review: Technological approaches, properties, and applications of pure and reinforced polyamide 6 (PA6) and polyamide 12 (PA12) composite materials,” Polymers, vol. 17, no. 4, 442, 2025. doi: https://doi.org/10.3390/polym17040442.
J.-J. Luo and I. M. Daniel, “Characterization and modeling of mechanical behavior of polymer/clay nanocomposites,” Composites Science and Technology, vol. 63, no. 11, pp. 1607–1616, 2003. doi: https://doi.org/10.1016/S0266-3538(03)00060-5.
S. Gul, A. Kausar, B. Muhammad, and S. Jabeen, “Research progress on properties and applications of polymer/clay nanocomposite,” Polymer-Plastics Technology and Engineering, vol. 55, no. 7, pp. 684–703, 2016. doi: https://doi.org/10.1080/03602559.2015.1098699.
M. Mozetič, “Plasma-stimulated super-hydrophilic surface finish of polymers,” Polymers, vol. 12, no. 11, 2498, 2020. doi: https://doi.org/10.3390/polym12112498.
P. L. Sant’Ana, J. R. Bortoleto, and S. F. Durrant, “Contact angle and wettability of commercial polymers after plasma treatment,” London Journal of Engineering Research, vol. 22, no. 7, pp. 13–33, 2022. [Online]. Available: https://journalspress.com/contact-angle-and-wettability-of-commercial-polymers-studies-after-treatment/.
G. Primc and M. Mozetič, “Surface modification of polymers by plasma treatment for appropriate adhesion of coatings,” Materials, vol. 17, no. 7, 1494, 2024. doi: https://doi.org/10.3390/ma17071494.
F. R. Oliveira, F. Steffens, P. S. B. de Holanda, J. H. O. do Nascimento, K. N. Matsui, and A. P. Souto, “Physical, chemical and morphological characterization of polyamide fabrics treated with plasma discharge,” Materials Research, vol. 20, Suppl. 2, pp. 60–68, 2017. doi: https://doi.org/10.1590/1980-5373-MR-2016-1032.
Downloads
Key Dates
Received
Revised
Accepted
Published Online First
Published
Issue
Section
License
Copyright (c) 2026 Akram A. Al-Asadi, Abdulrazzaq S Abdullah, Adnan A. Ateeq, Kadhim H. Hassan , Alaa Almansoori (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
