DESIGN AND SIMULATION OF HIGH GAIN SEPIC DC–DC CONVERTER

Authors

  • Ihsan A. Mejbel Electrical Engineering Department, Mustansiriyah University, Baghdad, Iraq Author
  • Turki K. Hassan Electrical Engineering Department, Mustansiriyah University, Baghdad, Iraq Author

DOI:

https://doi.org/10.31272/jeasd.27.1.12

Keywords:

SEPIC, high static gain, voltage stress, ripples, DC-DC converter

Abstract

This paper proposes a new model of the converter, a single-ended primary-inductor converter (SEPIC) type with a high gain voltage for clean energy sources. The suggested model is established by combining the traditional SEPIC DC-DC converter with two different circuits. The first circuit is a split-inductor circuit that is made of three diodes and two inductors, while the second circuit consists of two capacitors and two diodes. The suggested SEPIC DC-DC converter achieves a high voltage gain of 7.5 times the supply voltage when the duty cycle value is kept at 0.5 with only a unique controlled switch. The gain of the proposed converter is greatly increased while the ripple of output voltage and the input current is decreased for higher values of the duty cycle. In addition, the decreased value of the input current ripple results in limited switching stress. The suggested converter is analyzed in detail for continuous conduction mode (CCM). A MATLAB/ Simulink program is used to confirm the analysis of the suggested converter.

References

F. Blaabjerg, Y. Yang, K. Ma, and X. Wang, “Power electronics-the key technology for renewable energy system integration,” in 2015 International Conference on Renewable Energy Research and Applications (ICRERA), 2015, pp. 1618–1626.

O. Cornea, G.-D. Andreescu, N. Muntean, and D. Hulea, Bidirectional power flow control in a DC microgrid through a switched-capacitor cell hybrid DC–DC converter, vol. 64, no. 4. IEEE, 2016.

S. Padmanaban, M. S. Bhaskar, P. K. Maroti, F. Blaabjerg, and V. Fedák, “An original transformer and switched-capacitor (T & SC)-based extension for DC-DC boost converter for high-voltage/low-current renewable energy applications: Hardware implementation of a new T & SC boost converter,” Energies, vol. 11, no. 4, p. 783, 2018.

R. W. Erickson and D. Maksimovic, Fundamentals of power electronics. Springer Science & Business Media, 2007.

M. R. Banaei and S. G. Sani, “Analysis and implementation of a new SEPIC-based single-switch buck–boost DC–DC converter with continuous input current,” IEEE Trans. power Electron., vol. 33, no. 12, pp. 10317–10325, 2018.

H. Suryoatmojo, I. Dilianto, R. Mardiyanto, E. Setijadi, and D. C. Riawan, “Design and analysis of high gain modified SEPIC converter for photovoltaic applications,” in 2018 IEEE International Conference on Innovative Research and Development (ICIRD), 2018, pp. 1–6.

M. Zhang, Y. Xing, H. Wu, H. Hu, and X. Ma, “A dual coupled inductors-based high step-up/step-down bidirectional dc-dc converter for energy storage system,” in 2017 IEEE Applied Power Electronics Conference and Exposition (APEC), 2017, pp. 2958–2963.

D. Yu, J. Yang, R. Xu, Z. Xia, H. H.-C. Iu, and T. Fernando, “A family of module-integrated high step-up converters with dual coupled inductors,” IEEE Access, vol. 6, pp. 16256–16266, 2018.

Y. Cao, V. Samavatian, K. Kaskani, and H. Eshraghi, “A novel nonisolated ultra-high-voltage-gain DC–DC converter with low voltage stress,” IEEE Trans. Ind. Electron., vol. 64, no. 4, pp. 2809–2819, 2016.

G. Wu, X. Ruan, and Z. Ye, “Nonisolated high step-up DC–DC converters adopting switched-capacitor cell,” IEEE Trans. Ind. Electron., vol. 62, no. 1, pp. 383–393, 2014.

Z. Zhang, O. C. Thomsen, M. A. E. Andersen, and H. R. Nielsen, “Dual-input isolated full-bridge boost dc–dc converter based on the distributed transformers,” IET Power Electron., vol. 5, no. 7, pp. 1074–1083, 2012.

H. Wen, B. Su, and W. Xiao, “Design and performance evaluation of a bidirectional isolated dc–dc converter with extended dual-phase-shift scheme,” IET Power Electron., vol. 6, no. 5, pp. 914–924, 2013.

E. Ragonese et al., “A fully integrated galvanically isolated DC-DC converter with data communication,” IEEE Trans. Circuits Syst. I Regul. Pap., vol. 65, no. 4, pp. 1432–1441, 2017.

S. A. Gorji, M. Ektesabi, and J. Zheng, “Isolated switched-boost push–pull DC–DC converter for step-up applications,” Electron. Lett., vol. 53, no. 3, pp. 177–179, 2017.

K.-H. Chao and Y.-C. Jheng, “A soft-switching coupled inductor bidirectional DC–DC converter with high-conversion ratio,” Int. J. Electron., vol. 105, no. 1, pp. 164–190, 2018.

P. Akter, M. Uddin, S. Mekhilef, N. M. L. Tan, and H. Akagi, “Model predictive control of bidirectional isolated DC–DC converter for energy conversion system,” Int. J. Electron., vol. 102, no. 8, pp. 1407–1427, 2015.

C. Sakthivel, K. Selvakumar, and T. Venkatesan, “Modified SEPIC converter with high static gain for renewable energy applications,” in IJCTA, vol. 9, no. 37, International Science Press, 2016, pp. 865–873.

D. Kumar, R. A. Gupta, and H. Tiwari, “A Novel High Voltage Gain SEPIC Converter Based on Hybrid Split-Inductor for Renewable Application,” IETE J. Res., pp. 1–17, 2020.

H. Ardi and A. Ajami, “Study on a high voltage gain SEPIC-based DC–DC converter with continuous input current for sustainable energy applications,” IEEE Trans. power Electron., vol. 33, no. 12, pp. 10403–10409, 2018.

S.-W. Lee and H.-L. Do, “Isolated SEPIC DC–DC converter with ripple-free input current and lossless snubber,” IEEE Trans. Ind. Electron., vol. 65, no. 2, pp. 1254–1262, 2017.

Downloads

Key Dates

Published

2023-01-01

How to Cite

A. Mejbel, I. . ., & K. Hassan, T. . (2023). DESIGN AND SIMULATION OF HIGH GAIN SEPIC DC–DC CONVERTER. Journal of Engineering and Sustainable Development, 27(1), 138-148. https://doi.org/10.31272/jeasd.27.1.12

Similar Articles

11-20 of 500

You may also start an advanced similarity search for this article.